Selamat Datang!
Gabung Sekarang
|
Masuk
Menu Anggota
|
Bantuan
|
0
SEMUA
PRODUK
JUAL
BELI
PERUSAHAAN
Mengenalkan Indotrade.co.id kepada teman
*
artinya harus diisi
*
Nama Anda:
*
Email Anda:
*
Email Teman Anda: :
Untuk mengirim lebih dari satu orang, pisahkan setiap email dengan koma.
Contoh: nama1@domain.co.id, nama2@domain.co.id dan seterusnya
*
Pesan:
Halo, Saya Pebisnis Saya mengenal produk ini dari https://www.indotrade.co.id dan saya lihat hal ini mungkin berguna untuk anda. ------------------------------------------------------- MEGGER DLRO 10X Low Resistance Ohmmeter This Megger DLRO-10X digital low resistance ohmmeter uses a menu system controlled by a two-axis paddle to allow manual selection of the test current. DLRO10X also adds real-time download of results and on-board storage for later download to a PC. Built into a strong, lightweight case that is equally at home in the field or in the laboratory. Light enough to be worn around the neck, they are small enough to be taken into areas which were previously too small to access. The DLRO 10X has a large, backlit LCD display. Uses a menu system controlled by a two-axis paddle to allow the user to manually select the maximum test current. DLRO 10X displays both forward and reverse measurements as well as the average of the two. DLRO 10X allows the user to set high and low pass limits, thereby enabling simple go-no-go testing. At the end of a test DLRO10X will store the test results, as well as any notes relevant to the test. Features: Accurate results in under three seconds Auto current reversal cancels standing emfs Fuse protected to 600 V NiMH battery reduces weight 250 mW power limit ( with optional override) to avoid heating the test sample Automatically detects continuity in potential and current connections Visible warning of high voltages present at the terminals Visible warning of current flowing in the test sample Multiple operating modes including fully automatic Alpha-numeric keypad for entering test notes User setable high and low limits Autoranging with Manual option Printer output and memory Normal mode initiates a test by pressing the Test button on the instrument front panel after connecting the test leads. Continuity of all four connections is checked, forward and reverse currents are applied. Auto mode allows forward and reverse current measurements to be made and the average displayed simply by making contact with all four probes. This mode is ideal when working with the supplied handspikes. Each time the probes are removed and reconnected to the load another test will be performed without the need to press the test button on the instrument. Continuous mode allows repeated measurements to be made on the same sample. Simply connect the test leads and press the test button. The measurement is updated every 3 seconds until the circuit is broken. Inductive mode is intended for use when measuring inductive loads. When measuring inductive loads it is necessary to wait for the voltage to stabilise. This means that the measurement could take a few seconds or several minutes. The test leads are firmly connected to the item to be measured and the Test button is pressed. The instrument will pass a current through the sample and wait for the voltage to stabilise. If possible the current will be increased. This procedure will be repeated until the voltage detected falls into the range 15 mV to 200 mV. The instrument will then continue to take readings, which will gradually decrease to the true value as the voltage stabilises further. The operator decides when the result is stable and presses the Test button to terminate the test. Measurement is made with forward current only. Unidirectional mode, on DLRO 10X only, applies a current in one direction only. This does not enable any standing emfs to be negated but speeds up the measurement process. Test starts automatically when probes are connected. Applications: The needs for accurate low resistance measurement are well known and very diverse. They range through Goods Receiving inspection of components to ground bonding and welded joints. Typical applications include, but are not limited to, making d.c. resistance measurements of: Switch and contact breaker resistance Busbar and cable joints Aircraft frame bonds and static control circuits Integrity of welded joints Inter-cell connections on battery systems up to 600 V peak Quality control of resistive components Transformer and motor winding resistance Rail and pipe bonds Metal alloys, welds and fuse resistance Graphite electrodes and other composites Wire and cable resistance Transmitter aerial and lightning conductor bonding Includes: 1 - EV6340-101 - 7 Ah NiMH battery module, 2 - EV6111-503 - DH4 Duplex handspikes, 1 - EV6280-333 - Battery Charger, 1 - EV6280-332 - Cigarette lighter charger, 1 - User Guide. Specifications: Resistance Range ( Ohms) : 1.9999m to 1999.9 Resolution: 0.1u to 100m Accuracy: + / -0.2% + / -0.2u Ohm ( Range Dependent) Output Current ( Amps) : 10A to 100uA Display: Backlit LCD Counts: 19, 999 Power Source: NiMH Battery Safety Rating: CAT III 600V Data Storage: 700 Tests, With Notes Interface: : RS232 Includes: ( 2) DH4 Duplex Handspikes, Battery Charger, Automotive Charger And Instructions Untuk informasi selengkapnya, silahkan ke http://www.indotrade.co.id/inst/2957941
0.0094 194.163.150.105