Hydro Cure Cartridge Filter[18 Feb. 2011, 4:43:07]
Keterangan
Hydro Cure Cartridge Filter | www.profilterindonesia.com | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter | Hydro Cure Cartridge Filter
In 1995 Filterpart-Indonesia developed and introduced Hydro-Cure® melt blown polypropylene sediment cartridges. Designed initially for the potable water market, today these cartridges are used in a wide variety of applications where economical filters are required.
Clack Hydro-Cure® Cartridges are manufactured on state-of-theart production equipment using
a computer controlled process to ensure reliability and performance.
Molten polypropylene is extruded into a high velocity air stream. The semi-molten fibers are collected and cooled on our patented take-off system.
Gradient depth filtration is achieved with our technically advanced die design. The inner most fibers form a tight self supporting matrix which eliminates the need for a separate center core and provides exceptional strength.
As a depth filter, Hydro-Cure® sediment cartridges trap particles throughout the entire cross
section of the filter. Larger particles are trapped on or near the surface of the filter and the
smaller particles are trapped throughout the inner layers of the cartridge. The gradient density design allows for optimum dirt holding capacity and minimal change-outs.
Hydro-Cure® melt blown filter cartridges are made of polypropylene resin meeting FDA regulation 21CFR177.1520. No binders, lubricants or anti-static agents are used in our manufacturing process. Filterpart-Indonesia melt blown polypropylene filters have been
tested and certified under ANSI/ NSF Standard 42 for material requirements only. The inert
polypropylene resin provides exceptional chemical compatibility to handle a wide range of
process fluids.
Hydro-Cure® cartridges are designed for knife edge seal housings to provide a positive
seal without the use of end caps or gaskets. Hydro-Cure cartridges are interchangeable with
most standard pleated, string wound and other melt blown cartridges.
Hydro-Cure® cartridges are designed to provide high flow rates with minimum pressure drop. Flow rates of up to 5 gpm per 10â length are recommended and should not exceed 10 gpm
per 10â length for optimal efficiency. The maximum operating temperature is 100° F ( 38° C) .
Hydro-Cure® filters are available in 1, 5, 25 and 50 micron ratings and will fit most standard filter housings. Standard filter lengths of 9 7/ 8â , 20â 30â and 40â are available. Cartridges are individually shrink wrapped and labeled. Hydro-Cure® sediment filters have the micron rating embossed on the side of every cartridge for easy identification.
Specialty lengths, diameters, micron ratings and private labeling are available. Please contact our Sales Department for further information.
Standard Filter Length 9 7/ 8â ( 25.1 cm) , 20â ( 50.8 cm) , 30â ( 76.2 cm) , 40â ( 101.6 cm)
Filter I.D 1 1/ 16â ( 2.7cm)
Filter O.D 2 ½ â ( 6.4 cm)
Nominal Micron Ratings 1, 5, 25, 50
Prioritas Indotrade Tahun ke-13
www.profilterindonesia.com
